Floor standing/Bench top
Closed loop down force control
Ultra high data acquisition
Mix and match module per need
Nano to macro range
Easy to add new modules in future
Imaging options like Interferometer, Confocal Microscope allows to create sub nm 3d images of the sample
Perform multiple ASTM, ISO, DIN tests
Nano nN to 3000mN, Micro 3000mN to 30N, Macro upto 10000N (more ranges available).
The High Frequency Reciprocating Rig- HFRR (ASTM D6079) to evaluate diesel fuel lubricity. The ball is caused to rub against the disk 1mm stroke at a frequency of 50 Hz for 75 min. Real time down force control , piezo sensors to measure inline friction makes this module very reliable and repeatable.
Close loop down force control from mN
Load profile – constant, linear, step
Various size liquid containers.
Tests can be carried out on collected samples from field or for research purpose.
Film formation studied by electrical contact potential (ECR) changes
Fast, highly repeatable measurements
Fully automated computer controlled
Easy to calibrate, comes with standard oil and samples
Humidity and temperature control and monitoring
* Standard Upper Specimen 6.0mm diameter ball (universal ball holder 1.6mm to 9mm available)
Module is mounted on XY Stage. Tests including Pin on Disk,Ball on Disk can be performed.
Module is mounted on XY Stage. Tests including Pin on plate,Ball on plate, Linear Wear Test can be performed.
Module is mounted on XY Stage. Rings, shafts, seals and more can be tested.
Upper sample is rotated which can be used with Z motion.
4Ball, Tapping, Drilling,Twist Compression
Tapping torque module allows to characterize friction, wear, torque etc. during forming and machining. The test involves tapping/drilling using taps of various standard sizes on materials of choice. Twist Compression is designed to measure friction and adhesion in metal forming. Test involves slowly rotating a ring on top of material of choice.
The standard Test to determine extreme pressure, friction wear properties of lubricant greases, solid bonded films, gear and hydraulic fluids, lubricating oils. All tests are done in oscillation mode under controlled environmental conditions. ASTM D5706, D5707, D6425, D7217, D7420, D7594 ,D7421 , DIN 51834 /2/3/4/5/6/7/8/9
The block on ring module is typically used to evaluate friction wear of materials, lubricant where a ring/bearing/shaft is rotated under axial load. ASTM G77, D2509, D2714, D2782, D2981, D3704
4 ball module is used to measure friction, wear and EP properties of oils and greases. The test involves rotating one ball on three stationary balls at controlled environmental conditions. Confirm to meet ASTM D2266, D4172, D5183, D2596, D2783, VW PV1444, PV1454, DIN51350-1, DIN51350-2, DIN51350-4, DIN51350-6, IP 300, IP 299, CEC L-45-A-00 (KRL) and more.
This test helps evaluate friction and wear parameters of piston ring liner material in presence of engine oils. Few applicable standards are ASTMG181-11 and more. The test setup allows to mount real pieces of actual piston ring and liners.
This test (ASTM 3702) helps evaluate friction and wear parameters of self-lubricated materials in thrust washers ASTM3702
The module allows to measure wear, friction while sliding using pin/ball on disk setup. ASTM G 99, DIN 50324
Stribeck curve is a plot between coefficient of friction and bearing number. In all modules listed above user can change the load and velocity to automatically plot Stribeck Curves with ease.
The tribometer comes with integrated imaging modules such as interferometer, AFM, Raman confocal microscope, for sub nm resolution, 3D surface imaging on the platform without taking sample out of tool.
Standard configuration has X,Y,Z plus an add on interchangeable motion axis drive. This unique multi axis drive combination allows to create any custom motion to simulate testing conditions close to real life scenario
Easy to swap modules. The clamps allow to swap the modules without the need of any additional tools.